ESP32-S2 WiFi Development Board (Pico Format)
This is a compact WiFi development board from Waveshare based on the ESP32-S2 with a pinout that supports most HATs designed for the Raspberry Pi Pico!
The board offers numerous peripheral interfaces, integrated low-power Wi-Fi System-on-Chip (SoC), USB-C connectivity and mass memory. Equipped with a hardware crypto accelerator, RNG, HMAC and Digital Signature module, it can meet the security requirements of the Internet of Things.
Multiple low-power operating states are available to satisfy power requirements in IoT, mobile devices, wearable electronics, smart home and other application scenarios.
We also stock a version with a 0.96" LCD!
Features
- Supports the Raspberry Pi Pico expansion board ecosystem
- Xtensa single-core 32-bit LX7 microprocessor, ESP32-S2FH4, support clock frequency up to 240 MHz
- Integrated 320KB SRAM, 128KB ROM, 8MB PSRAM, 4MB Flash memory
- Supports IEEE802.11 b/g/n, on-board 2.4 GHz WiFi ceramic antenna, up to 150 Mbps data transfer rate
- USB-C connector, no more plug orientation problem
- On-chip integrated full-speed USB OTG interface, LCD interface (8-bit serial RGB/8080/6800), TWAI controller (ISO11898-1 compatible), capacitive sensor GPIO, temperature sensor and RMT (TX/RX)
- On-board 1.8A current high-efficiency boost/buck DC-DC TPS63000 power supply IC
- Support a variety of low-power operating states for adjusting the optimal balance between communication distance, data rate and power consumption
- C/C++, MicroPython and CircuitPython Support
What's On Board
1) ESP32-S2FH4
- Xtensa single-core 32-bit LX7 microprocessor
2) APS6404L-3SQR-SN
- 8MB PSRAM
3) BOOT button
- BOOT button, press BOOT and then RESET button to enter download mode
4) RESET button
5) TPS63000DRCR
- High-efficiency DC-DC buck-boost chip
6) LED
- User LED (not power indicator)
7) USB Type-C connector
- For programming, serial printing, etc.
8) Pinout
- Compatible with Raspberry Pi Pico
9) USB test points
- Connecting to USB interface
10) BOOT test point
- Connecting to BOOT button
11) WiFi ceramic antenna
Package Contents
- 1x ESP32-S2-Pico (Standard Version)
Resources
Pinout
For more details, please check ESP32-S2 Datasheet, Chapter 3.10 Peripheral Pin Assignments, and the schematic
Original: $10.60
-65%$10.60
$3.71
Description
This is a compact WiFi development board from Waveshare based on the ESP32-S2 with a pinout that supports most HATs designed for the Raspberry Pi Pico!
The board offers numerous peripheral interfaces, integrated low-power Wi-Fi System-on-Chip (SoC), USB-C connectivity and mass memory. Equipped with a hardware crypto accelerator, RNG, HMAC and Digital Signature module, it can meet the security requirements of the Internet of Things.
Multiple low-power operating states are available to satisfy power requirements in IoT, mobile devices, wearable electronics, smart home and other application scenarios.
We also stock a version with a 0.96" LCD!
Features
- Supports the Raspberry Pi Pico expansion board ecosystem
- Xtensa single-core 32-bit LX7 microprocessor, ESP32-S2FH4, support clock frequency up to 240 MHz
- Integrated 320KB SRAM, 128KB ROM, 8MB PSRAM, 4MB Flash memory
- Supports IEEE802.11 b/g/n, on-board 2.4 GHz WiFi ceramic antenna, up to 150 Mbps data transfer rate
- USB-C connector, no more plug orientation problem
- On-chip integrated full-speed USB OTG interface, LCD interface (8-bit serial RGB/8080/6800), TWAI controller (ISO11898-1 compatible), capacitive sensor GPIO, temperature sensor and RMT (TX/RX)
- On-board 1.8A current high-efficiency boost/buck DC-DC TPS63000 power supply IC
- Support a variety of low-power operating states for adjusting the optimal balance between communication distance, data rate and power consumption
- C/C++, MicroPython and CircuitPython Support
What's On Board
1) ESP32-S2FH4
- Xtensa single-core 32-bit LX7 microprocessor
2) APS6404L-3SQR-SN
- 8MB PSRAM
3) BOOT button
- BOOT button, press BOOT and then RESET button to enter download mode
4) RESET button
5) TPS63000DRCR
- High-efficiency DC-DC buck-boost chip
6) LED
- User LED (not power indicator)
7) USB Type-C connector
- For programming, serial printing, etc.
8) Pinout
- Compatible with Raspberry Pi Pico
9) USB test points
- Connecting to USB interface
10) BOOT test point
- Connecting to BOOT button
11) WiFi ceramic antenna
Package Contents
- 1x ESP32-S2-Pico (Standard Version)
Resources
Pinout
For more details, please check ESP32-S2 Datasheet, Chapter 3.10 Peripheral Pin Assignments, and the schematic
