Fermion: 1.8" 128x160 IPS TFT LCD Display with MicroSD Slot
This ST7735S 1.8" TFT Display features a resolution of 128×160 and SPI (4-wire) communication. Integrated with a microSD card slot, it allows you to easily read full-colour bitmaps from the SD card.
The module provides you with two wiring methods: pin header and GDI (General Display interface). You can directly connect the display to a FireBeetle main controller using the included FPC cable. Plug n' play and easy to wire, the display supports a low refresh rate and offers a good display effect and strong versatility.
It can be used in applications such as sensor monitoring and alarm, an Arduino temperature monitor, fan controller and many more!
FireBeetle Wiring Example
Features
- 128x160 Resolution
- SPI (4-wire) communication
- Integrated with a microSD card slot
- GDI or pin header interface
Specification
- Operating Voltage: 3.3V-5V
- TFT Viewing Angle: 120 degrees
- Pixels: 128 columns x 160 rows
- Communication: SPI
- Interface Mode: GDI, pin header
- Driver Chip: ST7735S
- Full-screen Power Consumption: 0.11 W
- MicroSD Slot x 1
- Operating Temperature: -10℃ - +60℃
- Display Area: 26 mm x 35 mm
- Module Dimension: 34 mm x 55 mm
- Mounting Hole Pitch: 29 mm, 50 mm
- Mounting Hole Size: 2 mm
Package Contents
- 1x Fermion: 1.8" 128x160 IPS TFT LCD with MicroSD Card Slot
- 1x GDI Display Cable
- 1x 10P Pin Connector
Resources
Pinout
| Num | Label | Description |
| 1 | VCC | Power |
| 2 | GND | Ground |
| 3 | SCLK | Clock signal |
| 4 | MOSI | Receiving data |
| 5 | MISO | Transmitting data |
| 6 | CS | Screen Chip-select |
| 7 | RES | Reset |
| 8 | DC | Data/Command |
| 9 | BLK | Backlight |
| 10 | SDCS | SD card chip-select |
Description
This ST7735S 1.8" TFT Display features a resolution of 128×160 and SPI (4-wire) communication. Integrated with a microSD card slot, it allows you to easily read full-colour bitmaps from the SD card.
The module provides you with two wiring methods: pin header and GDI (General Display interface). You can directly connect the display to a FireBeetle main controller using the included FPC cable. Plug n' play and easy to wire, the display supports a low refresh rate and offers a good display effect and strong versatility.
It can be used in applications such as sensor monitoring and alarm, an Arduino temperature monitor, fan controller and many more!
FireBeetle Wiring Example
Features
- 128x160 Resolution
- SPI (4-wire) communication
- Integrated with a microSD card slot
- GDI or pin header interface
Specification
- Operating Voltage: 3.3V-5V
- TFT Viewing Angle: 120 degrees
- Pixels: 128 columns x 160 rows
- Communication: SPI
- Interface Mode: GDI, pin header
- Driver Chip: ST7735S
- Full-screen Power Consumption: 0.11 W
- MicroSD Slot x 1
- Operating Temperature: -10℃ - +60℃
- Display Area: 26 mm x 35 mm
- Module Dimension: 34 mm x 55 mm
- Mounting Hole Pitch: 29 mm, 50 mm
- Mounting Hole Size: 2 mm
Package Contents
- 1x Fermion: 1.8" 128x160 IPS TFT LCD with MicroSD Card Slot
- 1x GDI Display Cable
- 1x 10P Pin Connector
Resources
Pinout
| Num | Label | Description |
| 1 | VCC | Power |
| 2 | GND | Ground |
| 3 | SCLK | Clock signal |
| 4 | MOSI | Receiving data |
| 5 | MISO | Transmitting data |
| 6 | CS | Screen Chip-select |
| 7 | RES | Reset |
| 8 | DC | Data/Command |
| 9 | BLK | Backlight |
| 10 | SDCS | SD card chip-select |
